SMDA100 series 100w desktop power supply for medical equipment ? wide input voltage 90 to 264 vac, 47 to 63 hz ? iec - 320 - c14 input inlet ? single to triple output, output voltage available from 5vdc thru 40vdc ? input surge current, over voltage , output voltage and over load protection ? ultra - low leakage current (under 0.1 ma) ? active power factor correction ? on/off switch (optional) ? class i insulation 3 year warranty approvals: single output part number output voltage max. output current total regulation max. output power SMDA100 - s02 5 ~ 6 vdc 14.00 ~ 11.66 a 5% 70w SMDA100 - s03 6 ~ 8 vdc 13.33 ~ 10.00 a 5% 80w SMDA100 - s04 8 ~ 11 vdc 11.25 ~ 8.20 a 4% 90w SMDA100 - s05 12 ~ 13 vdc 8.33 ~ 7.70 a 3% 100w SMDA100 - s06 13 ~ 16 vdc 7.70 ~ 6.30 a 3% 100w SMDA100 - s07 16 ~ 21 vdc 6.30 ~ 4.80 a 3% 100w SMDA100 - s08 21 ~ 27 vdc 4.80 ~ 3.70 a 2% 100w SMDA100 - s09 27 ~ 33 vdc 3.70 ~ 3.00 a 2% 100w SMDA100 - s10 33 ~ 40 vdc 3.00 ~ 2.50 a 2% 100w multi output part number output 1 output 2 output 3 max. output power vonom iomin iomax regmax vonom iomin iomax regmax vonom iomin iomax regmax SMDA100 - d00 +3.3v 1.0a 10a 7% +12v 0.3a 3a 5% 69w SMDA100 - d01 +5v 1.0a 10a 5% +12v 0.3a 3a 5% 80w SMDA100 - d02 +5v 1.0a 10a 5% +15v 0.3a 3a 5% 80w SMDA100 - d03 +5v 1.0a 10a 5% +24v 0.2a 2a 5% 80w SMDA100 - d04 +3.3v 1.0a 10a 7% +5v 0.5a 5a 5% 55w SMDA100 - d09 +12v 0.7a 7a 5% - 12v 0a 1a 5% 80w SMDA100 - d10 +15v 0.6a 6a 5% - 15v 0a 1a 5% 80w SMDA100 - d12 +24v 0.3a 3a 5% - 24v 0a 1a 5% 80w SMDA100 - d15 +5v 1.0a 10a 5% - 24v 0a 1a 5% 74w SMDA100 - t00 +3.3v 1.0a 10a 7% +12v 0.3a 3a 5% - 12v 0a 1a 5% 74w SMDA100 - t00 - 1 +3.3v 1.0a 10a 7% +12v 0.3a 3a 5% +12v 0a 1a 5% 74w SMDA100 - t01 +5v 1.0a 10a 5% +12v 0.3a 3a 5% - 5v 0a 1a 5% 80w SMDA100 - t01 - 1 +5v 1.0a 10a 5% +12v 0.3a 3a 5% +5v 0a 1a 5% 80w SMDA100 - t02 +5v 1.0a 10a 5% +12v 0.3a 3a 5% - 12v 0a 1a 5% 80w SMDA100 - t02 - 1 +5v 1.0a 10a 5% +12v 0.3a 3a 5% +12v 0a 1a 5% 80w SMDA100 - t03 +5v 1.0a 10a 5% +15v 0.3a 3a 6% - 15v 0a 1a 5% 80w SMDA100 - t03 - 1 +5v 1.0a 10a 5% +15v 0.3a 3a 6% +15v 0a 1a 5% 80w SMDA100 - t04 +5v 1.0a 10a 5% +24v 0.3a 3a 5% - 24v 0a 1a 5% 80w SMDA100 - t04 - 1 +5v 1.0a 10a 5% +24v 0.3a 3a 5% +24v 0a 1a 5% 80w SMDA100 - t05 +5v 1.0a 10a 5% +24v 0.3a 3a 5% - 12v 0a 1a 5% 80w SMDA100 - t05 - 1 +5v 1.0a 10a 5% +24v 0.3a 3a 5% +12v 0a 1a 5% 80w SMDA100 - t06 +3.3v 1.0a 10a 7% +12v 0.3a 3a 5% - 5v 0a 1a 5% 74w SMDA100 - t06 - 1 +3.3v 1.0a 10a 7% +12v 0.3a 3a 5% +5v 0a 1a 5% 74w SMDA100 - t08 +3.3v 1.0a 10a 7% +5v 0.3a 3a 5% - 12v 0a 1a 5% 60w SMDA100 - t08 - 1 +3.3v 1.0a 10a 7% +5v 0.3a 3a 5% +12v 0a 1a 5% 60w s11 ,d00 doesn't have pse approvals. the model number of 105 had been approved by bsmi, kc, fcc.
electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 26 0 vac input frequency 47 63 hz power factor correction io=full load, vin=230 vac 0. 95 1 output power range vin= 90 to 264 va c 0 100 w input current (low line) io=full load, vin=115 vac 1.25 a input current (high line) io=full load, vin= 230 vac 0.5 a low line inrush current io=full load, 25c, cool start, vin=115vac 12 15 a high line inrush current io=full load, 25c, cool start, vin=230vac 26 30 a efficiency io=full load, vin=230vac 75 83 88 % line regulation io=full load 0.5 1 % load regulation vin=230vac 3 7 % over voltage protection 112 132 % over current protection 110 150 % transient response io=full load to half load, vin=100vac 4 ms hold - up time io=full load, vin=110vac 16 ms start up time io=full load, vin=100vac 0.3 1.5 2 s ripple & noise (peak to peak) * full load, vin=90vac 0.5 1 % safety ground leakage current io= full load, vin=240vac/60hz 0.1 ma temperature coefficient all output - 0.04 0.04 %/ c * note: the ripple & noise which is under 3.3vdc at 2% max. conditions parameter test conditions min. typ. max. unit operating temperature 0 5 0 70 c storage temperature - 40 85 c relative humidity 5 95 % operating temperature at 25 c , calculated per mil - hdbk - 217f 0.1 m hrs de - rate linearly from 100% load at 50c to 50% load at 70c approvals and compliances parameter test conditions min. unit dielectric withstanding voltage for primary to secondary primary to secondary 56 56 vdc dielectric withstanding voltage for primary to ground primary to ground 28 28 vdc isolation resistance test voltage = 5 00vdc 50 m emi requirements for cispr - 11 vin=220vac b class emi requirements for fcc part - 18 vin=110vac b class mechanical and pin out note: 1. dimensions are shown in inches and mm. 2. weight: 778 - 800g approx. (exclude the input cord) 3. optional output connector.
|
